[Linux-PowerEdge] [E] replacing a failed hard drive with PERC HBA mode

Kingston, Scott J scott.j.kingston at verizon.com
Thu Aug 10 08:00:52 CDT 2017


Tim,

Without having OMSA installed on the server, I believe that you have 3 options to recreate the vdisk.  You can either use the iDRAC and go to the Storage > Virtual Disks and section and select the Create tab.   This page should allow you to create the vdisk.

The other option is to go in through the LC and drill into the storage section to create the vdisk. This is my least favorite option.

Lastly, you could use the CRTL-R option during boot to open the Raid Controller setup page to re-create the vdisk.

Personally, I've had very good luck using the omsa tools and perform this function right from the linux command line.

Best Regards,
Scott

-----Original Message-----
From: linux-poweredge-bounces at dell.com [mailto:linux-poweredge-bounces at dell.com] On Behalf Of Tim Mooney
Sent: Wednesday, August 9, 2017 6:15 PM
To: linux-poweredge at dell.com
Subject: [E] [Linux-PowerEdge] replacing a failed hard drive with PERC HBA mode


Hi All!

I need to replace a hard drive in a Dell R720 that's running RHEL 6.9.
The problem is that the replacement drive shows up as "Ready" in the physical disks area of iDRAC, instead of "Online".  It does not automatically show up as a vdisk in the virtual disks area.

The PERC H710 mini is in HBA mode, not RAID mode, so it's not handling the mirroring.  That's being done at the OS level with Linux's mdadm.

This hard drive is part of an mdadm RAID1.  The drive failed completely, so mdadm failed each of the partitions out of the individual MD devices.
I removed the failed MD components and then forced the OS to forget about /dev/sdb, with

 	# echo 1 > /sys/block/sdb/device/delete

I pulled the failed hard drive from the hot-swap bay, installed the Dell replacement drive in the carrier, and inserted the replacement hard drive into the bay.  The drive LED blinked and went green, and iDRAC shows the physical disk as "Ready", instead of "Online", and the replacement is missing completely from the vdisk area.

The OS did not auto-detect a hard drive being added to the bus, and even a rescan via

 	# echo '- - -' > /sys/class/scsi_host/host0/scan

does not trigger it to recognize the replacement drive is there.  I'm guessing that's because I need to do something at the PERC/iDRAC/Lifecycle level to get the drive to switch to "Online" and make it a vdisk.

How do I go about doing that?

We do not currently have any Dell OS-level RPMs installed, so no omsa or srv-admin or whatever.  After being on this list for a couple of years, my confidence in those tools is extremely limited.

It seems like 'megaclisas' might be able to help, but I have been completely unable to find a working link to that tool, after the
LSI->Avago->Broadcomm transition.  If anyone has a working link to get
it, I would appreciate seeing it.

Could 'racadm' via ssh perform the necessary magic to get this drive so that the PERC is presenting it as a disk to the OS?  Is there something easier than that, that also doesn't require a huge mess of questionable Dell RPMs be installed?

Any suggestions are much appreciated,

Tim
-- 
Tim Mooney                                             Tim.Mooney at ndsu.edu
Enterprise Computing & Infrastructure                  701-231-1076 (Voice)
Room 242-J6, Quentin Burdick Building                  701-231-8541 (Fax)
North Dakota State University, Fargo, ND 58105-5164

_______________________________________________
Linux-PowerEdge mailing list
Linux-PowerEdge at dell.com
https://urldefense.proofpoint.com/v2/url?u=https-3A__lists.us.dell.com_mailman_listinfo_linux-2Dpoweredge&d=DwICAg&c=udBTRvFvXC5Dhqg7UHpJlPps3mZ3LRxpb6__0PomBTQ&r=sZA28jIebnZqNAL0vpYk2d6QxpNmuA4geqEmLP6D8ow&m=82TxaQbJOMVzeljnbvq5r-zW_CuQtGC5OAd5jupPX5k&s=VZCI5Y3JSZjjmFrYtVFxNqudRSycdwpEQtBs2x1tuaA&e= 



More information about the Linux-PowerEdge mailing list