PERC H200: boot message "mpt2sas0: sending diag reset !!"

Giulio giulioo at gmail.com
Wed Mar 17 09:57:53 CDT 2010


PET310, CentOS5.4, mpt2sas 02.00.02.00

At every boot I get some messages marked with multiple exclamation points.

mpt2sas0: sending diag reset !!
mpt2sas0: diag reset: SUCCESS

mpt2sas0: sending port enable !!

Are these normal or should I contact Dell support?

Thanks

=============
mpt2sas version 02.00.02.00 loaded
scsi0 : Fusion MPT SAS Host
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:03:00.0 to 64
mpt2sas0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3097884 kB)
mpt2sas0: PCI-MSI-X enabled: IRQ 50
mpt2sas0: iomem(0xdf2b0000), mapped(0xf88c0000), size(65536)
mpt2sas0: ioport(0xfc00), size(256)
mpt2sas0: sending diag reset !!
mpt2sas0: diag reset: SUCCESS
mpt2sas0: Allocated physical memory: size(750 kB)
mpt2sas0: Current Controller Queue Depth(490), Max Controller Queue
Depth(3439)
mpt2sas0: Scatter Gather Elements per IO(128)
mpt2sas0: LSISAS2008: FWVersion(02.15.57.00), ChipRevision(0x02),
BiosVersion(07.01.04.00)
mpt2sas0: Dell PERC H200 Adapter: Vendor(0x1000), Device(0x0072),
SSVID(0x1028), SSDID(0x1F1D)
mpt2sas0: Protocol=(Initiator,Target), Capabilities=(Raid,TLR,EEDP,Snapshot
Buffer,Diag Trace Buffer,Task Set Full,NCQ)
mpt2sas0: sending port enable !!
mpt2sas0: host_add: handle(0x0001), sas_addr(0x5a4badb013972700), phys(8)
mpt2sas0: port enable: SUCCESS
  Vendor: Dell      Model: Virtual Disk      Rev: 1028
  Type:   Direct-Access                      ANSI SCSI revision: 06
scsi 0:1:0:0: RAID1: handle(0x004f), wwid(0x009029b53f8f2a7b), pd_count(2),
type (SATA)
scsi 0:1:0:0: qdepth(128), tagged(1), simple(1), ordered(0), scsi_level(7),
cmd_que(1)
SCSI device sda: 487063552 512-byte hdwr sectors (249377 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 08
SCSI device sda: drive cache: write through
SCSI device sda: 487063552 512-byte hdwr sectors (249377 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 08
SCSI device sda: drive cache: write through
 sda: sda1 sda2 sda3 sda4
sd 0:1:0:0: Attached scsi disk sda
  Vendor: ATA       Model: WDC WD2502ABYS-1  Rev: 3B04
  Type:   Direct-Access                      ANSI SCSI revision: 05
scsi 0:0:0:0: SATA: handle(0x000a), sas_addr(0x4433221106000000),
device_name(0x4ee15001e9710289)
scsi 0:0:0:0: SATA: enclosure_logical_id(0x5a4badb013972700), slot(1)
scsi 0:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y),
sw_preserve(y)
scsi 0:0:0:0: qdepth(32), tagged(1), simple(1), ordered(0), scsi_level(6),
cmd_que(1)
  Vendor: ATA       Model: WDC WD2502ABYS-1  Rev: 3B04
  Type:   Direct-Access                      ANSI SCSI revision: 05
scsi 0:0:1:0: SATA: handle(0x000b), sas_addr(0x4433221107000000),
device_name(0x4ee150019df6028a)
scsi 0:0:1:0: SATA: enclosure_logical_id(0x5a4badb013972700), slot(0)
scsi 0:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y),
sw_preserve(y)
scsi 0:0:1:0: qdepth(32), tagged(1), simple(1), ordered(0), scsi_level(6),
cmd_que(1)

Thanks

-- 
giulioo at pobox.com



More information about the Linux-PowerEdge mailing list