PowerEdge 1950 with EMC AX4-5Dell

Łukasz Jagiełło jagiello.lukasz at gmail.com
Wed Sep 30 09:55:32 CDT 2009


Hi,

Everytime at boot got such errors:

#v+
QLogic Fibre Channel HBA Driver
ACPI: PCI Interrupt 0000:0c:00.0[A] -> GSI 16 (level, low) -> IRQ 169
qla2xxx 0000:0c:00.0: Found an ISP2432, irq 169, iobase 0xffffc2000001a000
qla2xxx 0000:0c:00.0: Configuring PCI space...
PCI: Setting latency timer of device 0000:0c:00.0 to 64
qla2xxx 0000:0c:00.0: Configure NVRAM parameters...
qla2xxx 0000:0c:00.0: Verifying loaded RISC code...
usb 1-5: new high speed USB device using ehci_hcd and address 4
qla2xxx 0000:0c:00.0: Allocated (64 KB) for EFT...
qla2xxx 0000:0c:00.0: Allocated (1413 KB) for firmware dump...
scsi1 : qla2xxx
qla2xxx 0000:0c:00.0:
 QLogic Fibre Channel HBA Driver: 8.02.00.06.05.03-k
  QLogic QLE2462 - PCI-Express to 4Gb FC, Dual Channel
  ISP2432: PCIe (2.5Gb/s x4) @ 0000:0c:00.0 hdma+, host#=1, fw=4.04.05
[IP] [Multi-ID] [84XX]
GSI 20 sharing vector 0xC9 and IRQ 20
ACPI: PCI Interrupt 0000:0c:00.1[B] -> GSI 17 (level, low) -> IRQ 201
qla2xxx 0000:0c:00.1: Found an ISP2432, irq 201, iobase 0xffffc2000001c000
qla2xxx 0000:0c:00.1: Configuring PCI space...
PCI: Setting latency timer of device 0000:0c:00.1 to 64
qla2xxx 0000:0c:00.1: Configure NVRAM parameters...
qla2xxx 0000:0c:00.1: Verifying loaded RISC code...
usb 1-5: configuration #1 chosen from 1 choice
hub 1-5:1.0: USB hub found
hub 1-5:1.0: 4 ports detected
qla2xxx 0000:0c:00.1: Allocated (64 KB) for EFT...
qla2xxx 0000:0c:00.1: Allocated (1413 KB) for firmware dump...
scsi2 : qla2xxx
qla2xxx 0000:0c:00.1:
 QLogic Fibre Channel HBA Driver: 8.02.00.06.05.03-k
  QLogic QLE2462 - PCI-Express to 4Gb FC, Dual Channel
  ISP2432: PCIe (2.5Gb/s x4) @ 0000:0c:00.1 hdma+, host#=2, fw=4.04.05
[IP] [Multi-ID] [84XX]
Initializing USB Mass Storage driver...
qla2xxx 0000:0c:00.0: LIP reset occured (f7f7).
qla2xxx 0000:0c:00.0: LIP occured (f7f7).
qla2xxx 0000:0c:00.0: LOOP UP detected (4 Gbps).
usb 3-2: new low speed USB device using uhci_hcd and address 2
qla2xxx 0000:0c:00.1: LIP reset occured (f7f7).
qla2xxx 0000:0c:00.1: LIP occured (f7f7).
qla2xxx 0000:0c:00.1: LOOP UP detected (4 Gbps).
usb 3-2: configuration #1 chosen from 1 choice
input:   USB Keyboard as /class/input/input0
input: USB HID v1.10 Keyboard [  USB Keyboard] on usb-0000:00:1d.1-2
input:   USB Keyboard as /class/input/input1
input: USB HID v1.10 Device [  USB Keyboard] on usb-0000:00:1d.1-2
  Vendor: DGC       Model: RAID 5            Rev: 0223
  Type:   Direct-Access                      ANSI SCSI revision: 04
SCSI device sdb: 2097152000 512-byte hdwr sectors (1073742 MB)
sdb: test WP failed, assume Write Enabled
sdb: asking for cache data failed
sdb: assuming drive cache: write through
SCSI device sdb: 2097152000 512-byte hdwr sectors (1073742 MB)
sdb: test WP failed, assume Write Enabled
sdb: asking for cache data failed
sdb: assuming drive cache: write through
 sdb:<6>sd 1:0:0:0: Device not ready: <6>: Current: sense key: Not Ready
    Add. Sense: Logical unit not ready, manual intervention required

end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
sd 1:0:0:0: Device not ready: <6>: Current: sense key: Not Ready
    Add. Sense: Logical unit not ready, manual intervention required

end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
sd 1:0:0:0: Device not ready: <6>: Current: sense key: Not Ready
    Add. Sense: Logical unit not ready, manual intervention required

end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
sd 1:0:0:0: Device not ready: <6>: Current: sense key: Not Ready
    Add. Sense: Logical unit not ready, manual intervention required

end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
sd 1:0:0:0: Device not ready: <6>: Current: sense key: Not Ready
    Add. Sense: Logical unit not ready, manual intervention required

end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
sd 1:0:0:0: Device not ready: <6>: Current: sense key: Not Ready
    Add. Sense: Logical unit not ready, manual intervention required

end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
sd 1:0:0:0: Device not ready: <6>: Current: sense key: Not Ready
    Add. Sense: Logical unit not ready, manual intervention required

end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
Dev sdb: unable to read RDB block 0
sd 1:0:0:0: Device not ready: <6>: Current: sense key: Not Ready
    Add. Sense: Logical unit not ready, manual intervention required
#v-

Any idea how turn off that ? OS is CentoOS 5.3. Kernel from CentOSplus.

Regards
-- 
Łukasz Jagiełło
lukasz<at>jagiello<dot>org



More information about the Linux-PowerEdge mailing list