Degraded controller but disks are ok ?

Ricardo Stella stella at rider.edu
Tue Apr 25 08:53:38 CDT 2006



Irwan Hadi wrote:
> Check the battery status of the controller whether it is OK or not.
>   
Battery is fine...

Is there a command to make it rescan ? I'm not sure I want to rebuild
it...  TIA.

Controller PERC 3/Di (Slot Embedded)
ID                 : 0
Status             : Ok
Name               : Battery 0
State              : Ready
Recharge Count     : Not Applicable
Max Recharge Count : Not Applicable

> On 4/24/06, Ricardo M. Stella <stella at rider.edu> wrote:
>   
>> Using OMSA 4.5 on a PE2650 (RHEL3 AS)
>>
>> Omreport shows the controller is degraded but the status of adisk and
>> vdisk is ok.  I do know the firmware should be upgraded but can't run the
>> updated firmware unless the state is ok.
>>
>> Any advice ? TIA...
>>
>> # omreport storage controller
>>  Controller  PERC 3/Di (Embedded)
>>
>> Controllers
>> ID                                : 0
>> Status                            : Non-Critical
>> Name                              : PERC 3/Di
>> Slot ID                           : Embedded
>> State                             : Degraded
>> Firmware Version                  : 2.8-0 (Bld 6082)
>> Driver Version                    : Not Applicable
>> Minimum Required Firmware Version : 2.8-0 (Bld 6092)
>> Minimum Required Driver Version   : Not Applicable
>> Number of Channels                : 2
>> Rebuild Rate                      : Not Applicable
>> Alarm State                       : Not Applicable
>> Cluster Mode                      : Not Applicable
>> SCSI Initiator ID                 : Not Applicable
>>
>> # omreport storage adisk controller=0
>> List of Array/Hard Disks on Controller PERC 3/Di (Embedded)
>>
>> Controller PERC 3/Di (Embedded)
>> ID                        : 0:0
>> Status                    : Ok
>> Name                      : Array Disk 0:0
>> State                     : Online
>> Progress                  : Not Applicable
>> Capacity                  : 136.72 GB (146798804992 bytes)
>> Used RAID Disk Space      : 136.72 GB (146798804992 bytes)
>> Available RAID Disk Space : 0.00 GB (0 bytes)
>> Hot Spare                 : No
>> Product ID                : IC35L146UCDY10-0
>> Revision                  : S27F
>> Vendor ID                 : IBM
>>
>> ID                        : 0:1
>> Status                    : Ok
>> Name                      : Array Disk 0:1
>> State                     : Online
>> Progress                  : Not Applicable
>> Capacity                  : 136.72 GB (146798804992 bytes)
>> Used RAID Disk Space      : 136.72 GB (146798804992 bytes)
>> Available RAID Disk Space : 0.00 GB (0 bytes)
>> Hot Spare                 : No
>> Product ID                : IC35L146UCDY10-0
>> Revision                  : S27F
>> Vendor ID                 : IBM
>>
>> # omreport storage vdisk
>> List of Virtual Disks in the System
>>
>> Controller PERC 3/Di (Embedded)
>> ID           : 0
>> Status       : Ok
>> Name         :
>> State        : Ready
>> Progress     : Not Applicable
>> Layout       : RAID-1
>> Size         : 136.72 GB (146798936064 bytes)
>> Device Name  : /dev/sda
>> Read Policy  : Read Cache Enabled
>> Write Policy : Write Cache Enabled Protected
>> Cache Policy : Not Applicable
>> Stripe Size  : Not Applicable
>>
>>
>> --
>> °(((=((===°°°(((===========================================
>>
>>
>> _______________________________________________
>> Linux-PowerEdge mailing list
>> Linux-PowerEdge at dell.com
>> http://lists.us.dell.com/mailman/listinfo/linux-poweredge
>> Please read the FAQ at http://lists.us.dell.com/faq
>>
>>     
>
>   

-- 

°(((=((===°°°(((===========================================

-------------- next part --------------
A non-text attachment was scrubbed...
Name: stella.vcf
Type: text/x-vcard
Size: 146 bytes
Desc: not available
Url : http://lists.us.dell.com/pipermail/linux-poweredge/attachments/20060425/b4490f8f/attachment.vcf 


More information about the Linux-PowerEdge mailing list