ext3-fs error on PE2650 (debian)

Peter J Milanese PMilanese at nypl.org
Thu Apr 6 14:09:41 CDT 2006


Silly me.

I didn't see the output from dmesg on my bb.



-----------------
Sent from my NYPL BlackBerry Handheld..... For the time being.


----- Original Message -----
From: linux-poweredge-bounces
Sent: 04/06/2006 03:05 PM
To: linux-poweredge <linux-poweredge at dell.com>
Subject: Re: ext3-fs error on PE2650 (debian)

his problem is he's using a perc3/di.  ugh.

0000:04:08.1 RAID bus controller: Dell PowerEdge Expandable RAID Controller 3/Di (rev 01)



Peter J Milanese wrote:
> I'd check firmware first.
>
> Is it on a perc?
>
> I had one case where a drive in a raid set was the problem and the esm did not report it. The system was just unstable at times.
>
>  
>
> -----------------
> Sent from my NYPL BlackBerry Handheld..... For the time being.
>
>
> ----- Original Message -----
> From: linux-poweredge-bounces
> Sent: 04/06/2006 02:43 PM
> To: <linux-poweredge at dell.com>
> Subject: ext3-fs error on PE2650 (debian)
>
> I came in this morning to find my PE2650 locked up spitting out errors to
> console:
>
> EXT-3-fs error (device sda10) in start_transaction: Journal has aborted
> scsi0 (0:0): rejecting I/O to offline device
> EXT-3-fs error (device sda9) in start_transaction: Journal has aborted
> scsi0 (0:0): rejecting I/O to offline device
>
> All I could do was reboot. The journals were recovered ok, and boot-up
> seemed fine. I checked my cron, and found that a few intensive jobs had
> started just before it locked up. I've read some people receiving this same
> message under under heavy I/O load.
> Has anyone else seen this behavior on their Dell? I have no idea where to
> start, any ideas?
>
> $uname -a
>   
>> Linux web 2.6.8-2-686-smp #1 SMP Tue Aug 16 12:08:30 UTC 2005 i686
>>     
> GNU/Linux
>
> $ lspci
> 0000:00:00.0 Host bridge: ServerWorks CMIC-LE Host Bridge (GC-LE chipset)
> (rev 32)
> 0000:00:00.1 Host bridge: ServerWorks CMIC-LE Host Bridge (GC-LE chipset)
> 0000:00:00.2 Host bridge: ServerWorks CMIC-LE Host Bridge (GC-LE chipset)
> 0000:00:04.0 ff00: Dell Embedded Remote Access or ERA/O
> 0000:00:04.1 ff00: Dell Remote Access Card III
> 0000:00:04.2 ff00: Dell Embedded Remote Access: BMC/SMIC device
> 0000:00:0e.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev
> 27)
> 0000:00:0f.0 Host bridge: ServerWorks CSB5 South Bridge (rev 93)
> 0000:00:0f.1 IDE interface: ServerWorks CSB5 IDE Controller (rev 93)
> 0000:00:0f.2 USB Controller: ServerWorks OSB4/CSB5 OHCI USB Controller (rev
> 05)
> 0000:00:0f.3 ISA bridge: ServerWorks CSB5 LPC bridge
> 0000:00:10.0 Host bridge: ServerWorks CIOB-X2 PCI-X I/O Bridge (rev 05)
> 0000:00:10.2 Host bridge: ServerWorks CIOB-X2 PCI-X I/O Bridge (rev 05)
> 0000:00:11.0 Host bridge: ServerWorks CIOB-X2 PCI-X I/O Bridge (rev 05)
> 0000:00:11.2 Host bridge: ServerWorks CIOB-X2 PCI-X I/O Bridge (rev 05)
> 0000:03:06.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5703X
> Gigabit Ethernet (rev 02)
> 0000:03:08.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5703X
> Gigabit Ethernet (rev 02)
> 0000:04:08.0 PCI bridge: Intel Corp. 80303 I/O Processor PCI-to-PCI Bridge
> (rev 01)
> 0000:04:08.1 RAID bus controller: Dell PowerEdge Expandable RAID Controller
> 3/Di (rev 01)
> 0000:05:06.0 SCSI storage controller: Adaptec RAID subsystem HBA (rev 01)
> 0000:05:06.1 SCSI storage controller: Adaptec RAID subsystem HBA (rev 01
>
> $dmesg
> Linux version 2.6.8-2-686-smp (horms at tabatha.lab.ultramonkey.org) (gcc
> version 3.3.5 (Debian 1:3.3.5-13)) #1 SMP Tue Aug 16 12:08:30 UTC 2005
> BIOS-provided physical RAM map:
>  BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
>  BIOS-e820: 0000000000100000 - 000000005fff0000 (usable)
>  BIOS-e820: 000000005fff0000 - 000000005fffec00 (ACPI data)
>  BIOS-e820: 000000005fffec00 - 000000005ffff000 (reserved)
>  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
>  BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
>  BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
> 639MB HIGHMEM available.
> 896MB LOWMEM available.
> found SMP MP-table at 000fe710
> On node 0 totalpages: 393200
>   DMA zone: 4096 pages, LIFO batch:1
>   Normal zone: 225280 pages, LIFO batch:16
>   HighMem zone: 163824 pages, LIFO batch:16
> DMI 2.3 present.
> ACPI: RSDP (v000 DELL                                      ) @ 0x000fdc60
> ACPI: RSDT (v001 DELL   PE2650   0x00000001 MSFT 0x0100000a) @ 0x000fdc74
> ACPI: FADT (v001 DELL   PE2650   0x00000001 MSFT 0x0100000a) @ 0x000fdca4
> ACPI: MADT (v001 DELL   PE2650   0x00000001 MSFT 0x0100000a) @ 0x000fdd18
> ACPI: SPCR (v001 DELL   PE2650   0x00000001 MSFT 0x0100000a) @ 0x000fdda0
> ACPI: DSDT (v001 DELL   PE2650   0x00000001 MSFT 0x0100000a) @ 0x00000000
> ACPI: PM-Timer IO Port: 0x808
> ACPI: Local APIC address 0xfee00000
> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> Processor #0 15:2 APIC version 20
> ACPI: LAPIC (acpi_id[0x02] lapic_id[0x06] enabled)
> Processor #6 15:2 APIC version 20
> ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
> Processor #1 15:2 APIC version 20
> ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] enabled)
> Processor #7 15:2 APIC version 20
> ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
> ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
> ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
> ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
> ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
> IOAPIC[0]: Assigned apic_id 8
> IOAPIC[0]: apic_id 8, version 17, address 0xfec00000, GSI 0-15
> ACPI: IOAPIC (id[0x09] address[0xfec01000] gsi_base[16])
> IOAPIC[1]: Assigned apic_id 9
> IOAPIC[1]: apic_id 9, version 17, address 0xfec01000, GSI 16-31
> ACPI: IOAPIC (id[0x0a] address[0xfec02000] gsi_base[32])
> IOAPIC[2]: Assigned apic_id 10
> IOAPIC[2]: apic_id 10, version 17, address 0xfec02000, GSI 32-47
> ACPI: IRQ9 used by override.
> Enabling APIC mode:  Flat.  Using 3 I/O APICs
> Using ACPI (MADT) for SMP configuration information
> Built 1 zonelists
> Kernel command line: root=/dev/sda1 ro 
> Initializing CPU#0
> PID hash table entries: 4096 (order 12: 32768 bytes)
> Detected 2785.781 MHz processor.
> Using pmtmr for high-res timesource
> Console: colour VGA+ 80x25
> Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> Memory: 1550656k/1572800k available (1663k kernel code, 20972k reserved,
> 772k data, 168k init, 655296k highmem)
> Checking if this processor honours the WP bit even in supervisor mode... Ok.
> Calibrating delay loop... 5505.02 BogoMIPS
> Security Scaffold v1.0.0 initialized
> Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
> CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
> CPU: After vendor identify, caps:  bfebfbff 00000000 00000000 00000000
> CPU: Trace cache: 12K uops, L1 D cache: 8K
> CPU: L2 cache: 512K
> CPU: Physical Processor ID: 0
> CPU: After all inits, caps:        bfebfbff 00000000 00000000 00000080
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
> CPU0: Thermal monitoring enabled
> Enabling fast FPU save and restore... done.
> Enabling unmasked SIMD FPU exception support... done.
> Checking 'hlt' instruction... OK.
> CPU0: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09
> per-CPU timeslice cutoff: 1463.00 usecs.
> task migration cache decay timeout: 2 msecs.
> enabled ExtINT on CPU#0
> ESR value before enabling vector: 00000040
> ESR value after enabling vector: 00000000
> Booting processor 1/1 eip 3000
> Initializing CPU#1
> masked ExtINT on CPU#1
> ESR value before enabling vector: 00000000
> ESR value after enabling vector: 00000000
> Calibrating delay loop... 5554.17 BogoMIPS
> CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
> CPU: After vendor identify, caps:  bfebfbff 00000000 00000000 00000000
> CPU: Trace cache: 12K uops, L1 D cache: 8K
> CPU: L2 cache: 512K
> CPU: Physical Processor ID: 0
> CPU: After all inits, caps:        bfebfbff 00000000 00000000 00000080
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#1.
> CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
> CPU1: Thermal monitoring enabled
> CPU1: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09
> Booting processor 2/6 eip 3000
> Initializing CPU#2
> masked ExtINT on CPU#2
> ESR value before enabling vector: 00000000
> ESR value after enabling vector: 00000000
> Calibrating delay loop... 5570.56 BogoMIPS
> CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
> CPU: After vendor identify, caps:  bfebfbff 00000000 00000000 00000000
> CPU: Trace cache: 12K uops, L1 D cache: 8K
> CPU: L2 cache: 512K
> CPU: Physical Processor ID: 3
> CPU: After all inits, caps:        bfebfbff 00000000 00000000 00000080
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#2.
> CPU2: Intel P4/Xeon Extended MCE MSRs (12) available
> CPU2: Thermal monitoring enabled
> CPU2: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09
> Booting processor 3/7 eip 3000
> Initializing CPU#3
> masked ExtINT on CPU#3
> ESR value before enabling vector: 00000000
> ESR value after enabling vector: 00000000
> Calibrating delay loop... 5554.17 BogoMIPS
> CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
> CPU: After vendor identify, caps:  bfebfbff 00000000 00000000 00000000
> CPU: Trace cache: 12K uops, L1 D cache: 8K
> CPU: L2 cache: 512K
> CPU: Physical Processor ID: 3
> CPU: After all inits, caps:        bfebfbff 00000000 00000000 00000080
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#3.
> CPU3: Intel P4/Xeon Extended MCE MSRs (12) available
> CPU3: Thermal monitoring enabled
> CPU3: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09
> Total of 4 processors activated (22183.93 BogoMIPS).
> ENABLING IO-APIC IRQs
> init IO_APIC IRQs
>  IO-APIC (apicid-pin) 9-0, 9-1, 9-2, 9-3, 9-4, 9-5, 9-6, 9-7, 9-8, 9-9,
> 9-10, 9-11, 9-12, 9-13, 9-14, 9-15, 10-0, 10-1, 10-2, 10-3, 10-4, 10-5,
> 10-6, 10-7, 10-8, 10-9, 10-10, 10-11, 10-12, 10-13, 10-14, 10-15 not
> connected.
> ..TIMER: vector=0x31 pin1=0 pin2=-1
> Using local APIC timer interrupts.
> calibrating APIC timer ...
> ..... CPU clock speed is 2784.0386 MHz.
> ..... host bus clock speed is 132.0589 MHz.
> checking TSC synchronization across 4 CPUs: passed.
> Brought up 4 CPUs
> CPU0:  online
>  domain 0: span 03
>   groups: 01 02
>   domain 1: span 0f
>    groups: 03 0c
> CPU1:  online
>  domain 0: span 03
>   groups: 02 01
>   domain 1: span 0f
>    groups: 03 0c
> CPU2:  online
>  domain 0: span 0c
>   groups: 04 08
>   domain 1: span 0f
>    groups: 0c 03
> CPU3:  online
>  domain 0: span 0c
>   groups: 08 04
>   domain 1: span 0f
>    groups: 0c 03
> checking if image is initramfs...it isn't (ungzip failed); looks like an
> initrd
> Freeing initrd memory: 4592k freed
> NET: Registered protocol family 16
> PCI: PCI BIOS revision 2.10 entry at 0xfc93e, last bus=5
> PCI: Using configuration type 1
> mtrr: v2.0 (20020519)
> ACPI: Subsystem revision 20040326
> ACPI: Interpreter enabled
> ACPI: Using IOAPIC for interrupt routing
> ACPI: PCI Root Bridge [PCI0] (00:00)
> PCI: Probing PCI hardware (bus 00)
> PCI: Ignoring BAR0-3 of IDE controller 0000:00:0f.1
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: PCI Root Bridge [PCI4] (00:04)
> PCI: Probing PCI hardware (bus 04)
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI4._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI4.ZION._PRT]
> ACPI: PCI Root Bridge [PCI3] (00:03)
> PCI: Probing PCI hardware (bus 03)
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI3._PRT]
> ACPI: PCI Root Bridge [PCI2] (00:02)
> PCI: Probing PCI hardware (bus 02)
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI2._PRT]
> ACPI: PCI Root Bridge [PCI1] (00:01)
> PCI: Probing PCI hardware (bus 01)
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT]
> ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 10 *11 12 14)
> ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LNK6] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LNK7] (IRQs 3 4 5 6 7 9 *10 11 12 14)
> ACPI: PCI Interrupt Link [LNK8] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LNK9] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *7 9 10 11 12 14)
> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14)
> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14)
> ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 *7 9 10 11 12 14)
> ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14)
> ACPI: PCI Interrupt Link [LN10] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LN11] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LN12] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LN13] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LN14] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LN15] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LN16] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LN17] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LN18] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LN19] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LN1A] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LN1B] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LN1C] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LN1D] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LN1E] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LN1F] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
> ACPI: PCI Interrupt Link [LUSB] (IRQs 3 4 *5 6 7 10 11 12 14)
> Linux Plug and Play Support v0.97 (c) Adam Belay
> PnPBIOS: Scanning system for PnP BIOS support...
> PnPBIOS: Found PnP BIOS installation structure at 0xc00fe2d0
> PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xe2f4, dseg 0x40
> PnPBIOS: Unknown tag '0x2', length '0'.
> PnPBIOS: Unknown tag '0x0', length '1'.
> PnPBIOS: Unknown tag '0x0', length '0'.
> PnPBIOS: Unknown tag '0xc', length '2'.
> PnPBIOS: Unknown tag '0x0', length '2'.
> PnPBIOS: Unknown tag '0xc', length '5'.
> pnp: 00:00: ioport range 0x800-0x890 has been reserved
> pnp: 00:00: ioport range 0x8a0-0x8af has been reserved
> pnp: 00:00: ioport range 0xb001-0xb001 has been reserved
> pnp: 00:00: ioport range 0xca8-0xcaa has been reserved
> pnp: 00:12: ioport range 0xc00-0xc01 has been reserved
> pnp: 00:12: ioport range 0xc06-0xc08 has been reserved
> pnp: 00:12: ioport range 0xc14-0xc14 has been reserved
> pnp: 00:12: ioport range 0xc50-0xc51 has been reserved
> pnp: 00:12: ioport range 0xc6f-0xc6f has been reserved
> pnp: 00:12: ioport range 0xcd6-0xcd7 has been reserved
> pnp: 00:12: ioport range 0xf50-0xf58 has been reserved
> PnPBIOS: 16 nodes reported by PnP BIOS; 16 recorded by driver
> PCI: Using ACPI for IRQ routing
> ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 177
> ACPI: PCI interrupt 0000:00:04.1[B] -> GSI 23 (level, low) -> IRQ 185
> ACPI: PCI interrupt 0000:00:04.2[C] -> GSI 27 (level, low) -> IRQ 193
> ACPI: PCI Interrupt Link [LUSB] enabled at IRQ 11
> ACPI: PCI interrupt 0000:00:0f.2[A] -> GSI 11 (level, low) -> IRQ 11
> ACPI: PCI interrupt 0000:04:08.1[A] -> GSI 30 (level, low) -> IRQ 201
> ACPI: PCI interrupt 0000:05:06.0[A] -> GSI 30 (level, low) -> IRQ 201
> ACPI: PCI interrupt 0000:05:06.1[B] -> GSI 31 (level, low) -> IRQ 209
> ACPI: PCI interrupt 0000:03:06.0[A] -> GSI 28 (level, low) -> IRQ 217
> ACPI: PCI interrupt 0000:03:08.0[A] -> GSI 29 (level, low) -> IRQ 225
> number of MP IRQ sources: 16.
> number of IO-APIC #8 registers: 16.
> number of IO-APIC #9 registers: 16.
> number of IO-APIC #10 registers: 16.
> testing the IO APIC.......................
> IO APIC #8......
> .... register #00: 08000000
> .......    : physical APIC id: 08
> .......    : Delivery Type: 0
> .......    : LTS          : 0
> .... register #01: 000F0011
> .......     : max redirection entries: 000F
> .......     : PRQ implemented: 0
> .......     : IO APIC version: 0011
> .... register #02: 08000000
> .......     : arbitration: 08
> .... IRQ redirection table:
>  NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
>  00 00F 0F  0    0    0   0   0    1    1    31
>  01 00F 0F  0    0    0   0   0    1    1    39
>  02 00F 0F  1    0    0   0   0    1    1    41
>  03 00F 0F  0    0    0   0   0    1    1    49
>  04 00F 0F  0    0    0   0   0    1    1    51
>  05 00F 0F  0    0    0   0   0    1    1    59
>  06 00F 0F  0    0    0   0   0    1    1    61
>  07 00F 0F  0    0    0   0   0    1    1    69
>  08 00F 0F  0    0    0   0   0    1    1    71
>  09 00F 0F  0    1    0   1   0    1    1    79
>  0a 00F 0F  0    0    0   0   0    1    1    81
>  0b 00F 0F  1    1    0   1   0    1    1    89
>  0c 00F 0F  0    0    0   0   0    1    1    91
>  0d 00F 0F  0    0    0   0   0    1    1    99
>  0e 00F 0F  0    0    0   0   0    1    1    A1
>  0f 00F 0F  0    0    0   0   0    1    1    A9
> IO APIC #9......
> .... register #00: 09000000
> .......    : physical APIC id: 09
> .......    : Delivery Type: 0
> .......    : LTS          : 0
> .... register #01: 000F0011
> .......     : max redirection entries: 000F
> .......     : PRQ implemented: 0
> .......     : IO APIC version: 0011
> .... register #02: 09000000
> .......     : arbitration: 09
> .... IRQ redirection table:
>  NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
>  00 000 00  1    0    0   0   0    0    0    00
>  01 000 00  1    0    0   0   0    0    0    00
>  02 000 00  1    0    0   0   0    0    0    00
>  03 00F 0F  1    1    0   1   0    1    1    B1
>  04 000 00  1    0    0   0   0    0    0    00
>  05 000 00  1    0    0   0   0    0    0    00
>  06 000 00  1    0    0   0   0    0    0    00
>  07 00F 0F  1    1    0   1   0    1    1    B9
>  08 000 00  1    0    0   0   0    0    0    00
>  09 000 00  1    0    0   0   0    0    0    00
>  0a 000 00  1    0    0   0   0    0    0    00
>  0b 00F 0F  1    1    0   1   0    1    1    C1
>  0c 00F 0F  1    1    0   1   0    1    1    D9
>  0d 00F 0F  1    1    0   1   0    1    1    E1
>  0e 00F 0F  1    1    0   1   0    1    1    C9
>  0f 00F 0F  1    1    0   1   0    1    1    D1
> IO APIC #10......
> .... register #00: 0A000000
> .......    : physical APIC id: 0A
> .......    : Delivery Type: 0
> .......    : LTS          : 0
> .... register #01: 000F0011
> .......     : max redirection entries: 000F
> .......     : PRQ implemented: 0
> .......     : IO APIC version: 0011
> .... register #02: 0A000000
> .......     : arbitration: 0A
> .... IRQ redirection table:
>  NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
>  00 000 00  1    0    0   0   0    0    0    00
>  01 000 00  1    0    0   0   0    0    0    00
>  02 000 00  1    0    0   0   0    0    0    00
>  03 000 00  1    0    0   0   0    0    0    00
>  04 000 00  1    0    0   0   0    0    0    00
>  05 000 00  1    0    0   0   0    0    0    00
>  06 000 00  1    0    0   0   0    0    0    00
>  07 000 00  1    0    0   0   0    0    0    00
>  08 000 00  1    0    0   0   0    0    0    00
>  09 000 00  1    0    0   0   0    0    0    00
>  0a 000 00  1    0    0   0   0    0    0    00
>  0b 000 00  1    0    0   0   0    0    0    00
>  0c 000 00  1    0    0   0   0    0    0    00
>  0d 000 00  1    0    0   0   0    0    0    00
>  0e 000 00  1    0    0   0   0    0    0    00
>  0f 000 00  1    0    0   0   0    0    0    00
> Using vector-based indexing
> IRQ to pin mappings:
> IRQ0 -> 0:0
> IRQ1 -> 0:1
> IRQ2 -> 0:2
> IRQ3 -> 0:3
> IRQ4 -> 0:4
> IRQ5 -> 0:5
> IRQ6 -> 0:6
> IRQ7 -> 0:7
> IRQ8 -> 0:8
> IRQ9 -> 0:9
> IRQ10 -> 0:10
> IRQ11 -> 0:11
> IRQ12 -> 0:12
> IRQ13 -> 0:13
> IRQ14 -> 0:14
> IRQ15 -> 0:15
> IRQ177 -> 1:3
> IRQ185 -> 1:7
> IRQ193 -> 1:11
> IRQ217 -> 1:12
> IRQ225 -> 1:13
> IRQ201 -> 1:14
> IRQ209 -> 1:15
> .................................... done.
> highmem bounce pool size: 64 pages
> VFS: Disk quotas dquot_6.5.1
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
> devfs: boot_options: 0x0
> Initializing Cryptographic API
> isapnp: Scanning for PnP cards...
> isapnp: No Plug & Play device found
> Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
> ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
> ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
> serio: i8042 AUX port at 0x60,0x64 irq 12
> serio: i8042 KBD port at 0x60,0x64 irq 1
> input: AT Translated Set 2 keyboard on isa0060/serio0
> NET: Registered protocol family 2
> IP: routing cache hash table of 16384 buckets, 128Kbytes
> TCP: Hash tables configured (established 524288 bind 65536)
> NET: Registered protocol family 8
> NET: Registered protocol family 20
> ACPI: (supports S0 S4 S5)
> RAMDISK: cramfs filesystem found at block 0
> RAMDISK: Loading 4592 blocks [1 disk] into ram disk... done.
> VFS: Mounted root (cramfs filesystem) readonly.
> Freeing unused kernel memory: 168k freed
> vesafb: probe of vesafb0 failed with error -6
> NET: Registered protocol family 1
> SCSI subsystem initialized
> Red Hat/Adaptec aacraid driver (1.1.2-lk2 Aug 16 2005)
> ACPI: PCI interrupt 0000:04:08.1[A] -> GSI 30 (level, low) -> IRQ 201
> AAC0: kernel 2.7.4 build 3170
> AAC0: monitor 2.7.4 build 3170
> AAC0: bios 2.7.0 build 3170
> AAC0: serial 36c861d3fafaf001
> scsi0 : percraid
> Using anticipatory io scheduler
>   Vendor: DELL      Model: PERCRAID RAID5    Rev: V1.0
>   Type:   Direct-Access                      ANSI SCSI revision: 02
> SCSI device sda: 286713856 512-byte hdwr sectors (146797 MB)
> sda: Write Protect is off
> sda: Mode Sense: 03 00 00 00
> SCSI device sda: drive cache: write through
>  /dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 p10 >
> Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
> EXT3-fs: INFO: recovery required on readonly filesystem.
> EXT3-fs: write access will be enabled during recovery.
> kjournald starting.  Commit interval 5 seconds
> EXT3-fs: sda1: orphan cleanup on readonly fs
> ext3_orphan_cleanup: deleting unreferenced inode 91400
> EXT3-fs: sda1: 1 orphan inode deleted
> EXT3-fs: recovery complete.
> EXT3-fs: mounted filesystem with ordered data mode.
> Adding 2097136k swap on /dev/sda5.  Priority:-1 extents:1
> EXT3 FS on sda1, internal journal
> Generic RTC Driver v1.07
> tg3.c:v3.10 (September 14, 2004)
> ACPI: PCI interrupt 0000:03:06.0[A] -> GSI 28 (level, low) -> IRQ 217
> tg3: tg3_request_firmware (eth%d): Couldn't get firmware "tg3/tso-1.4.0".
> tg3: eth%d: Firmware "tg3/tso-1.4.0" not loaded; continuing without TSO.
> eth0: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCIX:133MHz:64-bit)
> 10/100/1000BaseT Ethernet 00:0b:db:e6:92:43
> eth0: RXcsums[1] LinkChgREG[1] MIirq[1] ASF[0] Split[0] WireSpeed[1]
> TSOcap[0] 
> ACPI: PCI interrupt 0000:03:08.0[A] -> GSI 29 (level, low) -> IRQ 225
> tg3: tg3_request_firmware (eth%d): Couldn't get firmware "tg3/tso-1.4.0".
> tg3: eth%d: Firmware "tg3/tso-1.4.0" not loaded; continuing without TSO.
> eth1: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCIX:133MHz:64-bit)
> 10/100/1000BaseT Ethernet 00:0b:db:e6:92:44
> eth1: RXcsums[1] LinkChgREG[1] MIirq[1] ASF[0] Split[0] WireSpeed[1]
> TSOcap[0] 
> Capability LSM initialized
> device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm at uk.sistina.com
> kjournald starting.  Commit interval 5 seconds
> EXT3 FS on sda6, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting.  Commit interval 5 seconds
> EXT3 FS on sda7, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting.  Commit interval 5 seconds
> EXT3 FS on sda8, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting.  Commit interval 5 seconds
> EXT3 FS on sda9, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting.  Commit interval 5 seconds
> EXT3 FS on sda10, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> NET: Registered protocol family 10
> Disabled Privacy Extensions on device c031f0c0(lo)
> IPv6 over IPv4 tunneling driver
> tg3: eth0: Link is up at 1000 Mbps, full duplex.
> tg3: eth0: Flow control is off for TX and off for RX.
> eth0: no IPv6 routers present
> aacraid:Battery charge is now OK
>
> _______________________________________________
> Linux-PowerEdge mailing list
> Linux-PowerEdge at dell.com
> http://lists.us.dell.com/mailman/listinfo/linux-poweredge
> Please read the FAQ at http://lists.us.dell.com/faq
>
> _______________________________________________
> Linux-PowerEdge mailing list
> Linux-PowerEdge at dell.com
> http://lists.us.dell.com/mailman/listinfo/linux-poweredge
> Please read the FAQ at http://lists.us.dell.com/faq
>
>
>   

_______________________________________________
Linux-PowerEdge mailing list
Linux-PowerEdge at dell.com
http://lists.us.dell.com/mailman/listinfo/linux-poweredge
Please read the FAQ at http://lists.us.dell.com/faq



More information about the Linux-PowerEdge mailing list