Kernel panic: no init found

SHIBATA, Makoto ugya99 at yahoo.co.jp
Tue May 11 22:23:01 CDT 2004


Thank you Martin.

I change /etc/modules.conf.
alias scsi_hostadapter1 megaraid2
alias scsi_hostadapter2 megaraid2

System booted.




--- Martin Rheumer <martinr at hotkey.net.au> 
> I would change the megaraid to megaraid2
> and re-apply the up2date kernel.
> 
> Martin
> 
> 
> 
> 
> 
> At 09:16 AM 5/12/2004 +0900, you wrote:
> >Thank you Martin.
> >PowerEdge 1750
> >There is no megaraid_2002 in modules.conf
> >
> >Is this driver problem
> >
> ># cat /etc/modules.conf
> >alias parport_lowlevel parport_pc
> >alias scsi_hostadapter aic7xxx
> >options aic7xxx aic7xxx=no_probe
> >alias scsi_hostadapter1 megaraid
> >alias usb-controller usb-ohci
> >below usbkbd hid
> >alias eth0 bcm5700
> >alias eth1 bcm5700
> >alias scsi_hostadapter2 megaraid
> >#
> >
> >
> >#dmesg
> >...
> >SCSI subsystem driver Revision: 1.00
> >(scsi0) <Adaptec AIC-7899 Ultra 160/m SCSI host
> adapter>
> >found at PCI 1/4/0
> >(scsi0) Wide Channel A, SCSI ID=7, 32/255 SCBs
> >(scsi0) Downloading sequencer code... 396
> instructions
> >downloaded
> >(scsi1) <Adaptec AIC-7899 Ultra 160/m SCSI host
> adapter>
> >found at PCI 1/4/1
> >(scsi1) Wide Channel B, SCSI ID=7, 32/255 SCBs
> >(scsi1) Downloading sequencer code... 396
> instructions
> >downloaded
> >scsi0 : Adaptec AHA274x/284x/294x
> (EISA/VLB/PCI-Fast SCSI)
> >5.2.5/5.2.0
> >       <Adaptec AIC-7899 Ultra 160/m SCSI host
> adapter>
> >scsi1 : Adaptec AHA274x/284x/294x
> (EISA/VLB/PCI-Fast SCSI)
> >5.2.5/5.2.0
> >       <Adaptec AIC-7899 Ultra 160/m SCSI host
> adapter>
> >blk: queue c2116e18, I/O limit 4095Mb (mask
> 0xffffffff)
> >blk: queue c2116e18, I/O limit 4095Mb (mask
> 0xffffffff)
> >megaraid: v1.19.7 (Release Date: Tue Apr  8
> 12:01:41 EDT
> >2003)
> >megaraid: found 0x1028:0x000f:idx 0:bus 4:slot
> 3:func 0
> >scsi2 : Found a MegaRAID controller at 0xf8850000,
> IRQ: 7
> >scsi2 : Enabling 64 bit support
> >megaraid: [4.10:B111] detected 1 logical drives
> >megaraid: supports extended CDBs.
> >megaraid: channel[1] is raid.
> >megaraid: channel[2] is raid.
> >scsi2 : LSI Logic MegaRAID 4.10 254 commands 16
> targs 5
> >chans 7 luns
> >blk: queue f775b818, I/O limit 4095Mb (mask
> 0xffffffff)
> >scsi2: scanning virtual channel 0 for logical
> drives.
> >  Vendor: MegaRAID  Model: LD 0 RAID1   34G  Rev:
> 4.10
> >  Type:   Direct-Access                      ANSI
> SCSI
> >revision: 02
> >blk: queue f775ba18, I/O limit 4095Mb (mask
> 0xffffffff)
> >scsi2: scanning virtual channel 1 for logical
> drives.
> >scsi2: scanning virtual channel 2 for logical
> drives.
> >scsi2: scanning virtual channel 3 for logical
> drives.
> >scsi2: scanning physical channel 0 for devices.
> >  Vendor: PE/PV     Model: 1x3 SCSI BP       Rev:
> 1.1
> >  Type:   Processor                          ANSI
> SCSI
> >revision: 02
> >blk: queue f7526018, I/O limit 4095Mb (mask
> 0xffffffff)
> >scsi2: scanning physical channel 1 for devices.
> >Attached scsi disk sda at scsi2, channel 0, id 0,
> lun 0
> >SCSI device sda: 70774784 512-byte hdwr sectors
> (36237 MB)
> >Partition check:
> > sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8
> sda9 >
> >Journalled Block Device driver loaded
> >kjournald starting.  Commit interval 5 seconds
> >...
> >#
> >
> >
> >--- Martin Rheumer <martinr at hotkey.net.au>
> >> If you are like us and had Perc 3/Di controllers
> >> the modules changed for the raid controller..
> >> 
> >> Step back to the old kernel and the machine will
> >> boot then perform these steps..
> >> 
> >> rpm -e the new kernel versions.
> >> 
> >> Then change the /etc/modules.conf
> >> from megaraid_2002  megaraid2.
> >> 
> >> Then run the up2date command again.
> >> 
> >> This worked on 9 machines I just upgraded
> >> in the past 2 days....
> >> 
> >> 
> >> Martin
> >> 
> >> 
> >> 
> >> 
> >> At 19:19 11/05/2004 +0900, SHIBATA, Makoto wrote:
> >> >Redhat Enterprise 2.1AS
> >> >Dell 1750
> >> >
> >> >I update rpms from RHN.
> >> >from 2.4.9-e.3 to 2.4.9-e.40.
> >> >
> >> >Install successful end RHN gui.
> >> >
> >> >grub menu 
> >> >  Red Hat Linux (2.4.9-e.40smp)
> >> >  Red Hat Linux (2.4.9-e.40)
> >> >
> >> >fails
> >> >"Kernel panic: no init found"
> >> >
> >> >only
> >> >  Red Hat Linux Advanced Server-up (2.4.9-e.3)
> >> >boot normally.
> >> >
> >> >Dell 1750 has two cpus.
> >> >We want to use "2.4.9-e.40smp".
> >> >
> >> >Is there any procedure or tasks for kernel
> >> intallation
> >> >from RHN ?
> >> >
> >> >_______________________________________________
> >> >Linux-PowerEdge mailing list
> >> >Linux-PowerEdge at dell.com
> >>
>
>>http://lists.us.dell.com/mailman/listinfo/linux-poweredge
> >> >Please read the FAQ at
> http://lists.us.dell.com/faq
> >> or search the list
> >> archives at http://lists.us.dell.com/htdig/
> >> >
> >
> >_______________________________________________
> >Linux-PowerEdge mailing list
> >Linux-PowerEdge at dell.com
>
>http://lists.us.dell.com/mailman/listinfo/linux-poweredge
> >Please read the FAQ at http://lists.us.dell.com/faq
> or search the list
> archives at http://lists.us.dell.com/htdig/
> >




More information about the Linux-PowerEdge mailing list