Kernel panic: no init found

SHIBATA, Makoto ugya99 at yahoo.co.jp
Tue May 11 19:17:00 CDT 2004


Thank you Martin.
PowerEdge 1750
There is no megaraid_2002 in modules.conf

Is this driver problem

# cat /etc/modules.conf
alias parport_lowlevel parport_pc
alias scsi_hostadapter aic7xxx
options aic7xxx aic7xxx=no_probe
alias scsi_hostadapter1 megaraid
alias usb-controller usb-ohci
below usbkbd hid
alias eth0 bcm5700
alias eth1 bcm5700
alias scsi_hostadapter2 megaraid
#


#dmesg
...
SCSI subsystem driver Revision: 1.00
(scsi0) <Adaptec AIC-7899 Ultra 160/m SCSI host adapter>
found at PCI 1/4/0
(scsi0) Wide Channel A, SCSI ID=7, 32/255 SCBs
(scsi0) Downloading sequencer code... 396 instructions
downloaded
(scsi1) <Adaptec AIC-7899 Ultra 160/m SCSI host adapter>
found at PCI 1/4/1
(scsi1) Wide Channel B, SCSI ID=7, 32/255 SCBs
(scsi1) Downloading sequencer code... 396 instructions
downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI)
5.2.5/5.2.0
       <Adaptec AIC-7899 Ultra 160/m SCSI host adapter>
scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI)
5.2.5/5.2.0
       <Adaptec AIC-7899 Ultra 160/m SCSI host adapter>
blk: queue c2116e18, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c2116e18, I/O limit 4095Mb (mask 0xffffffff)
megaraid: v1.19.7 (Release Date: Tue Apr  8 12:01:41 EDT
2003)
megaraid: found 0x1028:0x000f:idx 0:bus 4:slot 3:func 0
scsi2 : Found a MegaRAID controller at 0xf8850000, IRQ: 7
scsi2 : Enabling 64 bit support
megaraid: [4.10:B111] detected 1 logical drives
megaraid: supports extended CDBs.
megaraid: channel[1] is raid.
megaraid: channel[2] is raid.
scsi2 : LSI Logic MegaRAID 4.10 254 commands 16 targs 5
chans 7 luns
blk: queue f775b818, I/O limit 4095Mb (mask 0xffffffff)
scsi2: scanning virtual channel 0 for logical drives.
  Vendor: MegaRAID  Model: LD 0 RAID1   34G  Rev: 4.10
  Type:   Direct-Access                      ANSI SCSI
revision: 02
blk: queue f775ba18, I/O limit 4095Mb (mask 0xffffffff)
scsi2: scanning virtual channel 1 for logical drives.
scsi2: scanning virtual channel 2 for logical drives.
scsi2: scanning virtual channel 3 for logical drives.
scsi2: scanning physical channel 0 for devices.
  Vendor: PE/PV     Model: 1x3 SCSI BP       Rev: 1.1
  Type:   Processor                          ANSI SCSI
revision: 02
blk: queue f7526018, I/O limit 4095Mb (mask 0xffffffff)
scsi2: scanning physical channel 1 for devices.
Attached scsi disk sda at scsi2, channel 0, id 0, lun 0
SCSI device sda: 70774784 512-byte hdwr sectors (36237 MB)
Partition check:
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 >
Journalled Block Device driver loaded
kjournald starting.  Commit interval 5 seconds
...
#


--- Martin Rheumer <martinr at hotkey.net.au>
> If you are like us and had Perc 3/Di controllers
> the modules changed for the raid controller..
> 
> Step back to the old kernel and the machine will
> boot then perform these steps..
> 
> rpm -e the new kernel versions.
> 
> Then change the /etc/modules.conf
> from megaraid_2002  megaraid2.
> 
> Then run the up2date command again.
> 
> This worked on 9 machines I just upgraded
> in the past 2 days....
> 
> 
> Martin
> 
> 
> 
> 
> At 19:19 11/05/2004 +0900, SHIBATA, Makoto wrote:
> >Redhat Enterprise 2.1AS
> >Dell 1750
> >
> >I update rpms from RHN.
> >from 2.4.9-e.3 to 2.4.9-e.40.
> >
> >Install successful end RHN gui.
> >
> >grub menu 
> >  Red Hat Linux (2.4.9-e.40smp)
> >  Red Hat Linux (2.4.9-e.40)
> >
> >fails
> >"Kernel panic: no init found"
> >
> >only
> >  Red Hat Linux Advanced Server-up (2.4.9-e.3)
> >boot normally.
> >
> >Dell 1750 has two cpus.
> >We want to use "2.4.9-e.40smp".
> >
> >Is there any procedure or tasks for kernel
> intallation
> >from RHN ?
> >
> >_______________________________________________
> >Linux-PowerEdge mailing list
> >Linux-PowerEdge at dell.com
>
>http://lists.us.dell.com/mailman/listinfo/linux-poweredge
> >Please read the FAQ at http://lists.us.dell.com/faq
> or search the list
> archives at http://lists.us.dell.com/htdig/
> >




More information about the Linux-PowerEdge mailing list