[Linux-PowerEdge] Automated setup config

Dan Yasny dyasny at gmail.com
Wed Nov 15 14:46:59 CST 2017


On Wed, Nov 15, 2017 at 3:27 PM, <Jose.Delarosa at dell.com> wrote:

> Dan,
>
>
>
> Correct, the Redfish APIs are only available in PowerEdge 12G, 13G and
> 14G, and the Redfish implementation differs a bit between them.
>

Does that mean I can talk to the iDRAC directly using REST? Also, is the
actual layout of the RESTful implementation for each version documented
somewhere?


>
>
> *Jose DelaRosa*
>
> Linux Engineering
>
> *Dell* *EMC*| Infrastructure Solutions Group
>
>
>
>
>
>
>
> *From:* Dan Yasny [mailto:dyasny at gmail.com]
> *Sent:* Wednesday, November 15, 2017 2:01 PM
> *To:* Delarosa, Jose <Jose_Delarosa at Dell.com>
> *Cc:* linux-poweredge-Lists <linux-poweredge at lists.us.dell.com>
> *Subject:* Re: [Linux-PowerEdge] Automated setup config
>
>
>
>
>
>
>
> On Wed, Nov 15, 2017 at 2:42 PM, <Jose.Delarosa at dell.com> wrote:
>
> Dan,
>
> If you are familiar with Ansible, you can use
> https://github.com/dell/idrac-ansible-module. This Ansible module uses
> Redfish APIs to manage PowerEdge servers via iDRAC. You can use the
> manage_bios.yml playbook to set boot mode to either UEFI or Legacy BIOS.
> Please note, however, that setting boot mode is only supported in 13G and
> 14G servers.
>
>
>
> Because the earlier generations don't support redfish, right?
>
>
>
>
> Once you have installed Ansible and followed the idrac-ansible-module
> setup instructions, you can run:
>
> To set UEFI mode: $ ansible-playbook manage_bios.yml --tags bootmodeuefi
> To set BIOS legacy mode: $ ansible-playbook manage_bios.yml --tags
> bootmodelegacybios
>
> After setting to either UEFI or BIOS boot mode, the server will be
> rebooted. Recommend to try first in 1-2 servers in /etc/ansible/hosts
> before you try in a larger number of servers, just so you get a feel for it
> first.
>
> Disclaimer: This Ansible module is not supported by Dell and some features
> are still under development. All features available in the playbooks are
> 100% functional, though some features are only available in later server
> generations.
>
>
>
> Still, this is great, thank you very much, exactly what I've been looking
> for
>
>
>
> Jose DelaRosa
> Linux Engineering
> Dell EMC| Infrastructure Solutions Group
>
>
>
> From: linux-poweredge-bounces-Lists On Behalf Of Dan Yasny
> Sent: Wednesday, November 15, 2017 10:02 AM
> To: linux-poweredge-Lists <linux-poweredge at lists.us.dell.com>
> Subject: [Linux-PowerEdge] Automated setup config
>
>
> Hi,
>
> I have a large amount of R320, R620 and R630's, all with iDRAC ENT
> installed. I need to do a bulk change in their setups, like switch all to
> BIOS boot or back to UEFI.
>
> Doing that host by host takes forever, but I couldn't find the way to
> automate such a change.
>
> Is there a way at all?
>
> Thanks,
> Dan
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.us.dell.com/pipermail/linux-poweredge/attachments/20171115/02da6d32/attachment-0001.html>


More information about the Linux-PowerEdge mailing list