PE1950 fan speed

[Vernon A. Fort]

michalwd1979 wrote:
> Hi Vernon,
> I am not 100% sure but I think that fan speed is set by BMC and you can not do anything about it. Simple test if fan speed control is working is to pull out one fan when server is running. For me (PE2850 running gentoo) this speeds-up other fans. When I putted it  back fans gradually slow down to normal speed. Can you check temperature of the CPUs using lm_sensors or openmanage or anything? In 2850 dell sets CPU warning temp to 120 deg, and maybe it assumes that running hot is normal for the system. 
> Anyway when I made a crash-test (a few compilations and a few cat /dev/urandom >/dev/null) some time ago I got about 62deg max on CPUs but I think this is because of completely changed cooling system.
>
> Regards,
> Michael
>
>
> Dnia 5 lutego 2008 3:46 "Vernon A. Fort" <vfort at provident-solutions.com> napisał(a):
>
>   
>> I have a PE1950 running gentoo.  During a cpu stress test, we expected 
>> the fan speed to go up but it did not.  We had the cpuload around 25.0 
>> and when i put my hand at the back of the server, it was very hot to the 
>> touch.  I have looked at the lm_sensors and the openipmi but i did not 
>> find anything related to controlling the fanspeed, i.e. making it go 
>> faster when under heavy load.
>>
>> Could someone point me to some good reading.  Basically - i need to 
>> monitor the server and have something that adjusts accordingly
>>     
After further reading, I enable some additional kernel features and 
installed ipmitool.  Why is the Temp disabled?  I obviouslly have 
something mis-configured in teh bios setup - any pointers....

Vernon

newcs ~ # ipmitool -I open sdr
Temp             | disabled          | ns
Temp             | disabled          | ns
Temp             | disabled          | ns
Temp             | disabled          | ns
Ambient Temp     | 26 degrees C      | ok
CMOS Battery     | 0x00              | ok
ROMB Battery     | 0x00              | ok
VCORE            | 0x01              | ok
VCORE            | 0x01              | ok
CPU VTT          | 0x01              | ok
1.5V PG          | 0x01              | ok
1.8V PG          | 0x01              | ok
3.3V PG          | 0x01              | ok
5V PG            | 0x01              | ok
1.5V PXH PG      | 0x01              | ok
5V Riser PG      | 0x01              | ok
Backplane PG     | 0x01              | ok
Linear PG        | 0x01              | ok
0.9V PG          | 0x01              | ok
0.9V Over Volt   | 0x01              | ok
CPU Power Fault  | 0x01              | ok
FAN MOD 1A RPM   | 7125 RPM          | ok
FAN MOD 1B RPM   | 7350 RPM          | ok
FAN MOD 1C RPM   | 4650 RPM          | ok
FAN MOD 1D RPM   | 4575 RPM          | ok
FAN MOD 2A RPM   | 7575 RPM          | ok
FAN MOD 2B RPM   | 7650 RPM          | ok
FAN MOD 2C RPM   | 4650 RPM          | ok
FAN MOD 2D RPM   | 4800 RPM          | ok
FAN MOD 3A RPM   | 8025 RPM          | ok
FAN MOD 3B RPM   | 7425 RPM          | ok
FAN MOD 3C RPM   | 4875 RPM          | ok
FAN MOD 3D RPM   | 4800 RPM          | ok
FAN MOD 4A RPM   | 7725 RPM          | ok
FAN MOD 4B RPM   | 7650 RPM          | ok
FAN MOD 4C RPM   | 4800 RPM          | ok
FAN MOD 4D RPM   | 4950 RPM          | ok
Presence         | 0x01              | ok
Presence         | 0x01              | ok
Presence         | 0x01              | ok
Presence         | 0x01              | ok
Presence         | 0x01              | ok
Presence         | 0x01              | ok
DRAC5 Conn 2 Cbl | Not Readable      | ns
PFault Fail Safe | Not Readable      | ns
Status           | 0x80              | ok
Status           | 0x80              | ok
Status           | 0x01              | ok
Status           | 0x0b              | ok
Status           | 0x01              | ok
RAC Status       | 0x00              | ok
OS Watchdog      | 0x00              | ok
SEL              | Not Readable      | ns
Intrusion        | 0x00              | ok
PS Redundancy    | 0x02              | ok
Fan Redundancy   | 0x01              | ok
CPU Temp Interf  | Not Readable      | ns
Drive            | 0x01              | ok
Cable SAS A      | 0x01              | ok
ECC Corr Err     | Not Readable      | ns
ECC Uncorr Err   | Not Readable      | ns
I/O Channel Chk  | Not Readable      | ns
PCI Parity Err   | Not Readable      | ns
PCI System Err   | Not Readable      | ns
SBE Log Disabled | Not Readable      | ns
Logging Disabled | Not Readable      | ns
Unknown          | 0xc0              | ok
CPU Protocol Err | Not Readable      | ns
CPU Bus PERR     | Not Readable      | ns
CPU Init Err     | Not Readable      | ns
CPU Machine Chk  | Not Readable      | ns
Memory Spared    | 0x00              | ok
Memory Mirrored  | 0x01              | ok
Memory RAID      | 0x01              | ok
Memory Added     | Not Readable      | ns
Memory Removed   | Not Readable      | ns
Memory Cfg Err   | 0x01              | ok
Mem Redun Gain   | 0x01              | ok
PCIE Fatal Err   | 0x01              | ok
Chipset Err      | 0x01              | ok
Err Reg Pointer  | 0x01              | ok
Mem ECC Warning  | 0x01              | ok
Mem CRC Err      | 0x01              | ok
USB Over-current | 0x01              | ok
POST Err         | Not Readable      | ns
Hdwr version err | Not Readable      | ns
Mem Overtemp     | 0x01              | ok
Mem Fatal SB CRC | 0x01              | ok
Mem Fatal NB CRC | 0x01              | ok