MD3000 on Debian.
Fábio Catunda
fcatunda at contactnet.com.br
Fri Dec 19 12:59:00 CST 2008
Hi Mark,
Here it goes
Thanks.
cture supported.
Intel machine check reporting enabled on CPU#3.
CPU3: Intel(R) Xeon(R) CPU E5410 @ 2.33GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 4/4 eip 3000
Initializing CPU#4
Calibrating delay using timer specific routine.. 4655.12 BogoMIPS
(lpj=9310259)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
000ce3bd 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000
000ce3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 000ce3bd
00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#4.
CPU4: Intel(R) Xeon(R) CPU E5410 @ 2.33GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 5/5 eip 3000
Initializing CPU#5
Calibrating delay using timer specific routine.. 4655.12 BogoMIPS
(lpj=9310253)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
000ce3bd 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000
000ce3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 000ce3bd
00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#5.
CPU5: Intel(R) Xeon(R) CPU E5410 @ 2.33GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 6/6 eip 3000
Initializing CPU#6
Calibrating delay using timer specific routine.. 4655.12 BogoMIPS
(lpj=9310249)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
000ce3bd 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000
000ce3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 2
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 000ce3bd
00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#6.
CPU6: Intel(R) Xeon(R) CPU E5410 @ 2.33GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 7/7 eip 3000
Initializing CPU#7
Calibrating delay using timer specific routine.. 4655.12 BogoMIPS
(lpj=9310248)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
000ce3bd 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000
000ce3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 3
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 000ce3bd
00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#7.
CPU7: Intel(R) Xeon(R) CPU E5410 @ 2.33GHz stepping 06
Total of 8 processors activated (37244.11 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 8 CPUs: passed.
Brought up 8 CPUs
migration_cost=57,12404
checking if image is initramfs... it is
Freeing initrd memory: 4392k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: PXH quirk detected, disabling MSI for SHPC device
Boot video device is 0000:0f:0d.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.PE2P._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX6._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SBEX._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.COMP._PRT]
ACPI: PCI Interrupt Link [LK00] (IRQs 3 4 5 *6 7 10 11 12)
ACPI: PCI Interrupt Link [LK01] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LK02] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LK03] (IRQs 3 4 *5 6 7 10 11 12)
ACPI: PCI Interrupt Link [LK04] (IRQs 3 4 5 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LK05] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK06] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LK07] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
pnp: 00:08: ioport range 0x800-0x87f could not be reserved
pnp: 00:08: ioport range 0x880-0x8bf has been reserved
pnp: 00:08: ioport range 0x8c0-0x8df has been reserved
pnp: 00:08: ioport range 0x8e0-0x8e3 has been reserved
pnp: 00:08: ioport range 0x900-0x900 has been reserved
pnp: 00:08: ioport range 0xc00-0xc7f has been reserved
pnp: 00:08: ioport range 0xca0-0xca7 has been reserved
pnp: 00:08: ioport range 0xca9-0xcab has been reserved
pnp: 00:09: ioport range 0xca8-0xca8 has been reserved
pnp: 00:09: ioport range 0xcac-0xcac has been reserved
PCI: Bridge: 0000:06:00.0
IO window: disabled.
MEM window: f4000000-f7ffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:05:00.0
IO window: disabled.
MEM window: f4000000-f7ffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:05:01.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:04:00.0
IO window: disabled.
MEM window: f4000000-f7ffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:04:00.3
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:02.0
IO window: disabled.
MEM window: f2000000-f7ffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:03.0
IO window: e000-efff
MEM window: fc700000-fc9fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:04.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:05.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:0c:00.0
IO window: d000-dfff
MEM window: fc400000-fc6fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:06.0
IO window: d000-dfff
MEM window: fc300000-fc6fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:07.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:02:00.0
IO window: disabled.
MEM window: f8000000-fbffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: f8000000-fbffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: c000-cfff
MEM window: fc100000-fc2fffff
PREFETCH window: d8000000-dfffffff
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:02.0 to 64
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:04:00.0 to 64
ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:05:00.0 to 64
PCI: Setting latency timer of device 0000:06:00.0 to 64
ACPI: PCI Interrupt 0000:05:01.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:05:01.0 to 64
PCI: Setting latency timer of device 0000:04:00.3 to 64
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:03.0 to 64
ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:04.0 to 64
PCI: Setting latency timer of device 0000:00:05.0 to 64
ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:06.0 to 64
PCI: Setting latency timer of device 0000:0c:00.0 to 64
PCI: Setting latency timer of device 0000:00:07.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
PCI: Setting latency timer of device 0000:02:00.0 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1229694326.548:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
Allocate Port Service[0000:00:02.0:pcie01]
PCI: Setting latency timer of device 0000:00:03.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.0:pcie00]
Allocate Port Service[0000:00:03.0:pcie01]
PCI: Setting latency timer of device 0000:00:04.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
Allocate Port Service[0000:00:04.0:pcie01]
PCI: Setting latency timer of device 0000:00:05.0 to 64
pcie_portdrv_probe->Dev[25e5:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:05.0:pcie00]
Allocate Port Service[0000:00:05.0:pcie01]
PCI: Setting latency timer of device 0000:00:06.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:06.0:pcie00]
Allocate Port Service[0000:00:06.0:pcie01]
PCI: Setting latency timer of device 0000:00:07.0 to 64
pcie_portdrv_probe->Dev[25e7:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:07.0:pcie00]
Allocate Port Service[0000:00:07.0:pcie01]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:04:00.0 to 64
Allocate Port Service[0000:04:00.0:pcie10]
Allocate Port Service[0000:04:00.0:pcie11]
PCI: Setting latency timer of device 0000:05:00.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:05:00.0:pcie20]
Allocate Port Service[0000:05:00.0:pcie21]
PCI: Setting latency timer of device 0000:05:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:05:01.0:pcie20]
Allocate Port Service[0000:05:01.0:pcie21]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
hpet_resources: 0xfed00000 is busy
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Starting balanced_irq
Using IPI No-Shortcut mode
ACPI: (supports S0 S4 S5)
Freeing unused kernel memory: 196k freed
Time: tsc clocksource has been installed.
ACPI: CPU0 (power states: C1[C1] C3[C3])
ACPI: CPU4 (power states: C1[C1] C3[C3])
ACPI: CPU2 (power states: C1[C1] C3[C3])
ACPI: CPU6 (power states: C1[C1] C3[C3])
ACPI: CPU1 (power states: C1[C1] C3[C3])
ACPI: CPU5 (power states: C1[C1] C3[C3])
ACPI: CPU3 (power states: C1[C1] C3[C3])
ACPI: CPU7 (power states: C1[C1] C3[C3])
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.4.44 (August 10, 2006)
ACPI: PCI Interrupt 0000:07:00.0[A] -> GSI 16 (level, low) -> IRQ 169
eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz
found at mem f4000000, IRQ 169, node addr 00221951b774
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 169
eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz
found at mem f8000000, IRQ 169, node addr 00221951b772
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Fusion MPT base driver 3.04.01
Copyright (c) 1999-2005 LSI Logic Corporation
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 21 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 66, io base 0x0000bce0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Fusion MPT SAS Host driver 3.04.01
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 20 (level, low) -> IRQ 74
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 74, io base 0x0000bcc0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 21 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 66, io base 0x0000bca0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 20 (level, low) -> IRQ 74
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 74, io base 0x0000bc80
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
mptbase: Initiating ioc0 bringup
usb 2-2: new low speed USB device using uhci_hcd and address 2
usb 2-2: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: Dell Dell USB Keyboard as /class/input/input0
input: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1d.1-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ioc0: SAS1068E: Capabilities={Initiator}
PCI: Setting latency timer of device 0000:01:00.0 to 64
scsi0 : ioc0: LSISAS1068E, FwRev=00192f00h, Ports=1, MaxQ=266, IRQ=169
Vendor: SEAGATE Model: ST973402SS Rev: S229
Type: Direct-Access ANSI SCSI revision: 05
Vendor: SEAGATE Model: ST973402SS Rev: S229
Type: Direct-Access ANSI SCSI revision: 05
Vendor: Dell Model: VIRTUAL DISK Rev: 1028
Type: Direct-Access ANSI SCSI revision: 05
ACPI: PCI Interrupt 0000:0d:08.0[A] -> GSI 16 (level, low) -> IRQ 169
mptbase: Initiating ioc1 bringup
ioc1: SAS1068: Capabilities={Initiator}
scsi1 : ioc1: LSISAS1068, FwRev=000a3300h, Ports=1, MaxQ=366, IRQ=169
Vendor: DELL Model: MD3000 Rev: 0670
Type: Direct-Access ANSI SCSI revision: 05
Vendor: DELL Model: Universal Xport Rev: 0670
Type: Direct-Access ANSI SCSI revision: 05
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 21 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 66, io mem 0xfca00000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
SCSI device sda: 142082048 512-byte hdwr sectors (72746 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 08
SCSI device sda: drive cache: write through
SCSI device sda: 142082048 512-byte hdwr sectors (72746 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 08
SCSI device sda: drive cache: write through
sda: sda1 sda2 sda3
sd 0:1:0:0: Attached scsi disk sda
SCSI device sdb: 3512197120 512-byte hdwr sectors (1798245 MB)
sdb: Write Protect is off
sdb: Mode Sense: 77 00 10 08
SCSI device sdb: drive cache: write back w/ FUA
SCSI device sdb: 3512197120 512-byte hdwr sectors (1798245 MB)
sdb: Write Protect is off
sdb: Mode Sense: 77 00 10 08
SCSI device sdb: drive cache: write back w/ FUA
sdb:<6>ESB2: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 169
ESB2: chipset revision 9
ESB2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
usb 5-5: new high speed USB device using ehci_hcd and address 3
usb 5-5: configuration #1 chosen from 1 choice
hub 5-5:1.0: USB hub found
hub 5-5:1.0: 4 ports detected
usb 2-2: USB disconnect, address 2
hda: TEAC DVD-ROM DV28EV, ATAPI CD/DVD-ROM drive
usb 2-2: new low speed USB device using uhci_hcd and address 3
end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
unable to read partition table
sd 1:0:0:0: Attached scsi disk sdb
SCSI device sdc: 40960 512-byte hdwr sectors (21 MB)
sdc: Write Protect is off
sdc: Mode Sense: 77 00 10 08
SCSI device sdc: drive cache: write through w/ FUA
SCSI device sdc: 40960 512-byte hdwr sectors (21 MB)
sdc: Write Protect is off
sdc: Mode Sense: 77 00 10 08
SCSI device sdc: drive cache: write through w/ FUA
sdc: unknown partition table
sd 1:0:0:31: Attached scsi disk sdc
end_request: I/O error, dev sdc, sector 48
Buffer I/O error on device sdc, logical block 6
Buffer I/O error on device sdc, logical block 7
Buffer I/O error on device sdc, logical block 8
Buffer I/O error on device sdc, logical block 9
Buffer I/O error on device sdc, logical block 10
Buffer I/O error on device sdc, logical block 11
Buffer I/O error on device sdc, logical block 12
Buffer I/O error on device sdc, logical block 13
usb 2-2: configuration #1 chosen from 1 choice
input: Dell Dell USB Keyboard as /class/input/input1
input: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1d.1-2
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 24X DVD-ROM drive, 198kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
end_request: I/O error, dev sdb, sector 3512196992
end_request: I/O error, dev sdb, sector 3512196992
end_request: I/O error, dev sdb, sector 3512197112
end_request: I/O error, dev sdb, sector 3512197112
end_request: I/O error, dev sdb, sector 3512197112
end_request: I/O error, dev sdb, sector 3512197112
end_request: I/O error, dev sdb, sector 3512197112
end_request: I/O error, dev sdb, sector 3512197112
end_request: I/O error, dev sdb, sector 3512197056
printk: 11 messages suppressed.
Buffer I/O error on device sdb, logical block 439024632
end_request: I/O error, dev sdb, sector 3512197104
end_request: I/O error, dev sdb, sector 3512197112
end_request: I/O error, dev sdb, sector 3512197112
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
printk: 8 messages suppressed.
Buffer I/O error on device sdb, logical block 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
printk: 8 messages suppressed.
Buffer I/O error on device sdb, logical block 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
printk: 8 messages suppressed.
Buffer I/O error on device sdb, logical block 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
end_request: I/O error, dev sdc, sector 48
input: PC Speaker as /class/input/input2
intel_rng: FWH not detected
Real Time Clock Driver v1.12ac
end_request: I/O error, dev sdb, sector 3512196992
end_request: I/O error, dev sdb, sector 3512196992
end_request: I/O error, dev sdb, sector 3512197112
printk: 17 messages suppressed.
Buffer I/O error on device sdb, logical block 439024639
end_request: I/O error, dev sdb, sector 3512197112
end_request: I/O error, dev sdb, sector 3512197112
floppy0: no floppy controllers found
end_request: I/O error, dev sdb, sector 3512197112
end_request: I/O error, dev sdb, sector 3512197112
end_request: I/O error, dev sdb, sector 3512197112
end_request: I/O error, dev sdb, sector 3512197056
end_request: I/O error, dev sdb, sector 3512197104
end_request: I/O error, dev sdb, sector 3512197112
end_request: I/O error, dev sdb, sector 3512197112
printk: 8 messages suppressed.
Buffer I/O error on device sdb, logical block 439024639
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
printk: 8 messages suppressed.
Buffer I/O error on device sdb, logical block 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
printk: 8 messages suppressed.
Buffer I/O error on device sdb, logical block 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
end_request: I/O error, dev sdb, sector 0
printk: 9 messages suppressed.
Buffer I/O error on device sdb, logical block 0
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised:
dm-devel at redhat.com
device-mapper: multipath: version 1.0.4 loaded
device-mapper: multipath round-robin: version 1.0.0 loaded
device-mapper: table: 254:0: multipath: error getting device
device-mapper: ioctl: error adding target to table
EXT3 FS on sda2, internal journal
end_request: I/O error, dev sdb, sector 0
device-mapper: multipath: Failing path 8:16.
loop: loaded (max 8 devices)
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
bnx2: eth1: using MSI
bnx2: eth1 NIC Link is Up, 100 Mbps full duplex
ipmi message handler version 39.0
IPMI System Interface driver.
ipmi_si: Trying SMBIOS-specified KCS state machine at I/O address 0xca8,
slave address 0x20, irq 0
ipmi: Found new BMC (man_id: 0x0002a2, prod_id: 0x0100, dev_id: 0x20)
IPMI KCS interface initialized
ipmi device interface
ACPI: Power Button (FF) [PWRF]
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
device-mapper: table: 254:2: multipath: error getting device
device-mapper: ioctl: error adding target to table
eth1: no IPv6 routers present
end_request: I/O error, dev sdb, sector 0
printk: 10 messages suppressed.
Buffer I/O error on device sdb, logical block 0
Buffer I/O error on device sdb, logical block 1
Buffer I/O error on device sdb, logical block 2
Buffer I/O error on device sdb, logical block 3
end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
Fusion MPT misc device (ioctl) driver 3.04.01
mptctl: Registered with Fusion MPT base driver
mptctl: /dev/mptctl @ (major,minor=10,220)
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
drivers/message/fusion/mptctl.c at 1914::mptctl_do_mpt_command - Target ID
out of bounds.
end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
Buffer I/O error on device sdb, logical block 1
Buffer I/O error on device sdb, logical block 2
Buffer I/O error on device sdb, logical block 3
end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
poweredgemark at gmail wrote:
> Hello,
>
> Can you provide the entire dmesg output?
>
> Thanks,
>
> Mark
>
> On Fri, Dec 19, 2008 at 12:10 PM, Fábio Catunda
> <fcatunda at contactnet.com.br <mailto:fcatunda at contactnet.com.br>> wrote:
>
> Hi list,
>
> This is my first message to the list, please let me know if some
> information is missing to help solve the problem.
>
> We have a MD3000 storage and we are trying to make it work with a
> PE1950
> server with Debian Etch.
>
> During the boot time the controller - SCSI storage controller: LSI
> Logic
> / Symbios Logic SAS1068 PCI-X Fusion-MPT SAS (rev 01) - shows the
> MD3000
> virtual disk and also shows the virtual disk capacity - 1.6TB, so I
> imagine that the storage is correctly configured.
>
> I already created the host on the storage and give it permission to
> access the virtual disk (Host-to-virtual-disk-mapping).
>
> On the host side I can see the controller with
> # omreport storage controller
> ID : 1
> Status : Ok
> Name : SAS 5/E
> Slot ID : PCI Slot 2
> State : Ready
> Firmware Version : 00.10.51.00.06.12.05.00
> Minimum Required Firmware Version : Not Applicable
> Driver Version : 3.04.01
> Minimum Required Driver Version : Not Applicable
> Number of Connectors : 2
> Rebuild Rate : Not Applicable
> BGI Rate : Not Applicable
> Check Consistency Rate : Not Applicable
> Reconstruct Rate : Not Applicable
> Alarm State : Not Applicable
> Cluster Mode : Not Applicable
> SCSI Initiator ID : Not Applicable
> Cache Memory Size : Not Applicable
> Patrol Read Mode : Not Applicable
> Patrol Read State : Not Applicable
> Patrol Read Rate : Not Applicable
> Patrol Read Iterations : Not Applicable
>
> WIth lsiutil I have:
> #lsiutil
> 1. /proc/mpt/ioc0 LSI Logic SAS1068E B3 105 00192f00
> 0
> 2. /proc/mpt/ioc1 LSI Logic SAS1068 B0 105 000a3300
> 0
>
> option 2 chosen, option 42 chosen shows:
> /proc/mpt/ioc1 is SCSI host 1
>
> B___T___L Type Operating System Device Name
> 0 0 0 Disk /dev/sdb [1:0:0:0]
> 0 0 31 Disk /dev/sdc [1:0:0:31]
>
> And finally I try to cfdisk /dev/sdb and I get:
> FATAL ERROR: Cannot read disk drive
>
> And dmesg shows me:
> Buffer I/O error on device sdb, logical block 0
> Buffer I/O error on device sdb, logical block 1
> Buffer I/O error on device sdb, logical block 2
> Buffer I/O error on device sdb, logical block 3
> end_request: I/O error, dev sdb, sector 0
>
> I'm fighting against this error for a week now and I'm completely
> out of
> ideas. I tried to install LSI drivers from their site, but I couldn't
> find any instructions to compile the source and RPM fails to install.
>
> Well, I don't know what else I can do, what should I install and
> etc, if
> somebody can help me I'll be glad.
>
> Thanks a lot,
>
> Fabio Catunda.
>
>
>
> _______________________________________________
> Linux-PowerEdge mailing list
> Linux-PowerEdge at dell.com <mailto:Linux-PowerEdge at dell.com>
> http://lists.us.dell.com/mailman/listinfo/linux-poweredge
> Please read the FAQ at http://lists.us.dell.com/faq
>
>
More information about the Linux-PowerEdge
mailing list