detecting hdd for failure
linux-poweredge at holiday.sk
linux-poweredge at holiday.sk
Wed Apr 30 03:43:33 CDT 2008
It helped! works now:)
Thanks a lot
Dusan
>
> "modprobe mptctl
>
> has to executed before /etc/init.d/dataeng starts.
> Rainer Sabelka sabelka add iue dot tuwien dot ac dot at>"
>
> ( '/etc/init.d/dataeng stop ; modprobe mptctl ; /etc/init.d/dataeng start'
> )
>
> http://blog.loftninjas.org/?p=100
> https://subtrac.rc.sara.nl/oss/omsa_2_deb/wiki/FAQ
>
>
> -----Original Message-----
> From: linux-poweredge-bounces at dell.com
> [mailto:linux-poweredge-bounces at dell.com] On Behalf Of Dusan
> Sent: Tuesday, April 29, 2008 11:33 AM
> To: linux-poweredge at dell.com
> Subject: Re: detecting hdd for failure
>
> Thanks for replying.
> It seams there is no controller.
>
> Any help?
>
> lorank:~# omreport storage controller
> No controllers found
>
> lorank:~# omreport storage pdisk controller=0
> Invalid controller value. Read, controller=0
> No controllers found.
>
> lorank:~# omreport storage pdisk controller=1
> Invalid controller value. Read, controller=1
> No controllers found.
>
> Thanks
>
> Dusan
>
>
> Patrick_Boyd at Dell.com wrote:
>> Any output from 'omreport storage controller' or 'omreport storage pdisk
>> controller=0'? This would give you the information that you want.
>>
>> -----Original Message-----
>> From: linux-poweredge-bounces at dell.com
>> [mailto:linux-poweredge-bounces at dell.com] On Behalf Of Dusan
>> Sent: Tuesday, April 29, 2008 9:38 AM
>> To: linux-poweredge-Lists
>> Subject: detecting hdd for failure
>>
>> Hello,
>>
>> I'm running Debian Etch on my PowerEdge840 server, with SAS5iR, 2 HDD in
>> RAID1.
>>
>> I installed OMSA 5.3 and IPMITOOL with them I can control temps, fans,
>> processor etc.
>> but what I am not able to controll are hard disks.
>>
>> I can see my 2 disks with lshw, but is it enough?
>>
>> Could you help me please, how can I controll my 2 HDD for failure?
>> If one of the two disk get out how will I get noticed?
>>
>> I'm including some logs
>>
>> Thanks a lot
>>
>> Dusan
>>
>> lorank:~# omreport chassis
>> Health
>>
>> Main System Chassis
>>
>> SEVERITY : COMPONENT
>> Ok : Fans
>> Ok : Intrusion
>> Ok : Memory
>> Ok : Power Supplies
>> Ok : Processors
>> Ok : Temperatures
>> Ok : Voltages
>> Ok : Hardware Log
>>
>> ----------------------
>>
>> lorank:~# lshw
>> ...
>> *-scsi
>> description: SCSI storage controller
>> product: SAS1068 PCI-X Fusion-MPT SAS
>> vendor: LSI Logic / Symbios Logic
>> physical id: 8
>> bus info: pci at 02:08.0
>> logical name: scsi0
>> version: 01
>> width: 64 bits
>> clock: 66MHz
>> capabilities: scsi bus_master cap_list scsi-host
>> configuration: driver=mptsas latency=72 maxlatency=10
>> mingnt=64
>> resources: iomemory:fe9fc000-fe9fffff
>> iomemory:fe9e0000-fe9effff irq:169
>> *-disk:0 UNCLAIMED
>> description: SCSI Disk
>> product: WDC WD2500YS-18S
>> vendor: ATA
>> physical id: 0.0.0
>> bus info: scsi at 0:0.0.0
>> version: 6C07
>> serial: WD-WCANY4149595
>> capacity: 232GB
>> configuration: ansiversion=5
>> *-disk:1 UNCLAIMED
>> description: SCSI Disk
>> product: WDC WD2500YS-18S
>> vendor: ATA
>> physical id: 0.1.0
>> bus info: scsi at 0:0.1.0
>> version: 6C07
>> serial: WD-WCANY4186098
>> capacity: 232GB
>> configuration: ansiversion=5
>> *-disk:2
>> description: SCSI Disk
>> product: VIRTUAL DISK
>> vendor: Dell
>> physical id: 1.0.0
>> bus info: scsi at 0:1.0.0
>> logical name: /dev/sda
>> version: 1028
>> size: 231GB
>> capacity: 231GB
>> capabilities: partitioned partitioned:dos
>> configuration: ansiversion=5
>> *-volume:0
>> description: Linux filesystem partition
>> physical id: 1
>> bus info: scsi at 0:1.0.0,1
>> logical name: /dev/sda1
>> capacity: 37GB
>> capabilities: primary bootable
>> *-volume:1
>> description: Linux swap / Solaris partition
>> physical id: 2
>> bus info: scsi at 0:1.0.0,2
>> logical name: /dev/sda2
>> capacity: 1906MB
>> capabilities: primary nofs
>> *-volume:2
>> description: Linux filesystem partition
>> physical id: 3
>> bus info: scsi at 0:1.0.0,3
>> logical name: /dev/sda3
>> capacity: 192GB
>> capabilities: primary
>> ...
>> ---------------------------
>> lorank:~# omreport chassis biossetup
>> BIOS Setup
>>
>> General
>> Attribute : Num Lock
>> Setting : On
>>
>> Attribute : Diskette
>> Setting : Auto
>>
>> Attribute : NIC
>> Setting : Enabled with PXE
>>
>> Attribute : USB
>> Setting : Enabled with BIOS support
>>
>> Attribute : IDE
>> Setting : Auto
>>
>> Attribute : Boot Sequence
>> Setting : Device List
>>
>> Attribute : Speaker
>> Setting : Off
>>
>> Attribute : CPU Virtualization Technology
>> Setting : Disabled
>>
>> Attribute : AC Power Recovery Mode
>> Setting : On
>>
>> Attribute : Embedded SATA Controller
>> Setting : Off
>>
>> Attribute : SATA Port 0
>> Setting : Off
>>
>> Attribute : SATA Port 1
>> Setting : Off
>>
>> Attribute : SATA Port 2
>> Setting : Off
>>
>> Attribute : SATA Port 3
>> Setting : Off
>>
>> Attribute : IDE Primary Drive 0
>> Setting : Auto
>>
>> Attribute : IDE Primary Drive 1
>> Setting : Off
>>
>> Attribute : Demand-Based Power Management
>> Setting : Disabled
>>
>> Serial Communications
>> Attribute : Serial Port 1
>> Setting : Com1
>>
>> Attribute : Console Redirection After Boot
>> Setting : Enabled
>>
>> Attribute : Console Redirection
>> Setting : Off
>>
>> Attribute : Console Redirection Failsafe BAUD Rate
>> Setting : 115200
>>
>>
>>
>> _______________________________________________
>> Linux-PowerEdge mailing list
>> Linux-PowerEdge at dell.com
>> http://lists.us.dell.com/mailman/listinfo/linux-poweredge
>> Please read the FAQ at http://lists.us.dell.com/faq
>>
>
> _______________________________________________
> Linux-PowerEdge mailing list
> Linux-PowerEdge at dell.com
> http://lists.us.dell.com/mailman/listinfo/linux-poweredge
> Please read the FAQ at http://lists.us.dell.com/faq
>
More information about the Linux-PowerEdge
mailing list