detecting hdd for failure
Dusan
linux-poweredge at holiday.sk
Tue Apr 29 13:27:23 CDT 2008
Thanks for replying.
It seams there is no controller.
Any help?
lorank:~# omreport storage controller
No controllers found
lorank:~# omreport storage pdisk controller=0
Invalid controller value. Read, controller=0
No controllers found.
lorank:~# omreport storage pdisk controller=1
Invalid controller value. Read, controller=1
No controllers found.
Thanks
Dusan
Patrick_Boyd at Dell.com wrote:
> Any output from 'omreport storage controller' or 'omreport storage pdisk
> controller=0'? This would give you the information that you want.
>
> -----Original Message-----
> From: linux-poweredge-bounces at dell.com
> [mailto:linux-poweredge-bounces at dell.com] On Behalf Of Dusan
> Sent: Tuesday, April 29, 2008 9:38 AM
> To: linux-poweredge-Lists
> Subject: detecting hdd for failure
>
> Hello,
>
> I'm running Debian Etch on my PowerEdge840 server, with SAS5iR, 2 HDD in
> RAID1.
>
> I installed OMSA 5.3 and IPMITOOL with them I can control temps, fans,
> processor etc.
> but what I am not able to controll are hard disks.
>
> I can see my 2 disks with lshw, but is it enough?
>
> Could you help me please, how can I controll my 2 HDD for failure?
> If one of the two disk get out how will I get noticed?
>
> I'm including some logs
>
> Thanks a lot
>
> Dusan
>
> lorank:~# omreport chassis
> Health
>
> Main System Chassis
>
> SEVERITY : COMPONENT
> Ok : Fans
> Ok : Intrusion
> Ok : Memory
> Ok : Power Supplies
> Ok : Processors
> Ok : Temperatures
> Ok : Voltages
> Ok : Hardware Log
>
> ----------------------
>
> lorank:~# lshw
> ...
> *-scsi
> description: SCSI storage controller
> product: SAS1068 PCI-X Fusion-MPT SAS
> vendor: LSI Logic / Symbios Logic
> physical id: 8
> bus info: pci at 02:08.0
> logical name: scsi0
> version: 01
> width: 64 bits
> clock: 66MHz
> capabilities: scsi bus_master cap_list scsi-host
> configuration: driver=mptsas latency=72 maxlatency=10
> mingnt=64
> resources: iomemory:fe9fc000-fe9fffff
> iomemory:fe9e0000-fe9effff irq:169
> *-disk:0 UNCLAIMED
> description: SCSI Disk
> product: WDC WD2500YS-18S
> vendor: ATA
> physical id: 0.0.0
> bus info: scsi at 0:0.0.0
> version: 6C07
> serial: WD-WCANY4149595
> capacity: 232GB
> configuration: ansiversion=5
> *-disk:1 UNCLAIMED
> description: SCSI Disk
> product: WDC WD2500YS-18S
> vendor: ATA
> physical id: 0.1.0
> bus info: scsi at 0:0.1.0
> version: 6C07
> serial: WD-WCANY4186098
> capacity: 232GB
> configuration: ansiversion=5
> *-disk:2
> description: SCSI Disk
> product: VIRTUAL DISK
> vendor: Dell
> physical id: 1.0.0
> bus info: scsi at 0:1.0.0
> logical name: /dev/sda
> version: 1028
> size: 231GB
> capacity: 231GB
> capabilities: partitioned partitioned:dos
> configuration: ansiversion=5
> *-volume:0
> description: Linux filesystem partition
> physical id: 1
> bus info: scsi at 0:1.0.0,1
> logical name: /dev/sda1
> capacity: 37GB
> capabilities: primary bootable
> *-volume:1
> description: Linux swap / Solaris partition
> physical id: 2
> bus info: scsi at 0:1.0.0,2
> logical name: /dev/sda2
> capacity: 1906MB
> capabilities: primary nofs
> *-volume:2
> description: Linux filesystem partition
> physical id: 3
> bus info: scsi at 0:1.0.0,3
> logical name: /dev/sda3
> capacity: 192GB
> capabilities: primary
> ...
> ---------------------------
> lorank:~# omreport chassis biossetup
> BIOS Setup
>
> General
> Attribute : Num Lock
> Setting : On
>
> Attribute : Diskette
> Setting : Auto
>
> Attribute : NIC
> Setting : Enabled with PXE
>
> Attribute : USB
> Setting : Enabled with BIOS support
>
> Attribute : IDE
> Setting : Auto
>
> Attribute : Boot Sequence
> Setting : Device List
>
> Attribute : Speaker
> Setting : Off
>
> Attribute : CPU Virtualization Technology
> Setting : Disabled
>
> Attribute : AC Power Recovery Mode
> Setting : On
>
> Attribute : Embedded SATA Controller
> Setting : Off
>
> Attribute : SATA Port 0
> Setting : Off
>
> Attribute : SATA Port 1
> Setting : Off
>
> Attribute : SATA Port 2
> Setting : Off
>
> Attribute : SATA Port 3
> Setting : Off
>
> Attribute : IDE Primary Drive 0
> Setting : Auto
>
> Attribute : IDE Primary Drive 1
> Setting : Off
>
> Attribute : Demand-Based Power Management
> Setting : Disabled
>
> Serial Communications
> Attribute : Serial Port 1
> Setting : Com1
>
> Attribute : Console Redirection After Boot
> Setting : Enabled
>
> Attribute : Console Redirection
> Setting : Off
>
> Attribute : Console Redirection Failsafe BAUD Rate
> Setting : 115200
>
>
>
> _______________________________________________
> Linux-PowerEdge mailing list
> Linux-PowerEdge at dell.com
> http://lists.us.dell.com/mailman/listinfo/linux-poweredge
> Please read the FAQ at http://lists.us.dell.com/faq
>
More information about the Linux-PowerEdge
mailing list