PERC info from SNMP

[Cody_Sparks at Dell.com]

Tom,

OpenManage SNMP Reference Guide:
http://support.dell.com/support/edocs/software/svradmin/5.0/en/snmp/html
/index.htm

Controller Firmware Version 
 Name
 controllerFWVersion
Object ID
 1.3.6.1.4.1.674.10893.1.20.130.1.1.8
Description
 Identifies the controller's current firmware version.
Syntax
 DisplayString
Access
 Read-only

--
Cody Sparks, RHCE
Dell Services
Server Support Analyst, Enterprise Expert Center
Dell Services Website
<http://www1.us.dell.com/content/topics/global.aspx/services/en/index?c=
us&cs=555&l=en&s=biz>

-----Original Message-----
From: linux-poweredge-bounces at dell.com
[mailto:linux-poweredge-bounces at dell.com] On Behalf Of Tom Haddon
Sent: Tuesday, August 22, 2006 9:52 AM
To: Boyd, Patrick
Cc: linux-poweredge-Lists
Subject: RE: PERC info from SNMP

Hi Patrick,

I do have SNMP installed, as I can query for all the other parameters,
it's just that when I did an snmp query to the top level Dell MIB:

snmpwalk -v1 -c <community> <host> enterprises.674.10892

I wasn't able to find any value corresponding to the PERC firmware
version. Can you let me know which OID it is?

Thanks, Tom

On Tue, 2006-08-22 at 09:44 -0500, Patrick_Boyd at Dell.com wrote:
> Yes you can do this via SNMP the omreport command was to test if 
> storage management is installed. If storage management is installed 
> then the data will be availabe via SNMP, CLI, or Webserver. If it is 
> not installed the data is not available.
> 
> -----Original Message-----
> From: Tom Haddon [mailto:tom at greenleaftech.net]
> Sent: Tuesday, August 22, 2006 9:43 AM
> To: Boyd, Patrick
> Cc: linux-poweredge-Lists
> Subject: RE: PERC info from SNMP
> 
> Hi Patrick,
> 
> So there's no way to do this via SNMP? I do have omreport installed, 
> but I'd like to run this across hundreds of servers.
> 
> Thanks, Tom
> 
> On Tue, 2006-08-22 at 09:18 -0500, Patrick_Boyd at Dell.com wrote:
> > Do you have storage management installed? You can check by running 
> > `omreport storage controller` on the host in question. That should 
> > give you the RAID card firmware version if storage management is
> installed.
> > 
> > -----Original Message-----
> > From: linux-poweredge-bounces at dell.com 
> > [mailto:linux-poweredge-bounces at dell.com] On Behalf Of Tom Haddon
> > Sent: Tuesday, August 22, 2006 9:09 AM
> > To: linux-poweredge-Lists
> > Subject: PERC info from SNMP
> > 
> > Hi Folks,
> > 
> > I've been able to successfully retrieve the following information 
> > via
> > snmpwalks:
> > 
> > snmpwalk -v1 -c <community> <host> OID (as below)
> > 
> > Server Model	 enterprises.674.10892.1.300.10.1.9.1		
> > O/S	enterprises.674.10892.1.400.10.1.6.1,
> > enterprises.674.10892.1.400.10.1.7.1		
> > BIOS Firmware enterprises.674.10892.1.300.50.1.8.1.1
> > 
> > BMC/ESM Firmware enterprises.674.10892.1.300.60.1.11.1.1		
> > Service Tag	enterprises.674.10892.1.300.10.1.11.1		
> > OMSA Version	enterprises.674.10892.1.100.10.0		
> > 
> > However, I can't seem to retrieve the Perc Firmware version.
> > 
> > Can anyone help out?
> > 
> > Thanks, Tom
> > 
> > --
> > Tom Haddon <tom at greenleaftech.net>
> > 
> > _______________________________________________
> > Linux-PowerEdge mailing list
> > Linux-PowerEdge at dell.com
> > http://lists.us.dell.com/mailman/listinfo/linux-poweredge
> > Please read the FAQ at http://lists.us.dell.com/faq

_______________________________________________
Linux-PowerEdge mailing list
Linux-PowerEdge at dell.com
http://lists.us.dell.com/mailman/listinfo/linux-poweredge
Please read the FAQ at http://lists.us.dell.com/faq